In the majority of cases it’s as easy as trimming the shrubs and mow the lawn. Sometimes, however it’s gotten slightly than you’d like and you’re faced with the decision of what to do to clear the overgrown lawn. This step-by step guide will give all the necessary information to know about clearing the brush in the backyard of your home, from best hand tools to the most efficient brushes clearing tools to a different strategy that will allow you to boost the effectiveness of your efforts.
How to clear an overgrown land?
Check out your land
It’s not like building a house without blueprints or an action plan and clearing the of your lawn is no different. Although you don’t require to have a detailed map for your yard, you have to stroll through it and figure out the best method to get rid of the undergrowth and brush. Note any trees you wish to be removed and mark the areas that seem to be particularly thick in overgrowth. It’s also beneficial to record any areas in your yard that could be difficult to work on, like rocky or swampy terrain, or overgrowth that is interspersed with fencing.
Plan for brush disposal
Based on the nature of the work you’re undertaking your trash collection schedule could not be sufficient to take care of the yard waste. You may also not be able to get rid of the brush until it is timed to coincide with your next collection day. You can think about other options including composting or the backyard trash dumpster rental. From limbs and dirt to brush and shrubs renting a dumpster is an effective method of getting rid of your yard that is overgrown on your schedule. Not certain if a dumpster is the right choice for you? Read the lawn waste guide to discover all the options and reasons why it is possible to rent a dumpster.
Cut down the trees
In the section for preparation you marked the trees that you want to remove. This is the last chance to reconsider your decision because trees removal will be the initial task to be done. Removing smaller trees can be easy enough to tackle on your own. However, larger and medium size trees could be hazardous to remove without the proper equipment. For trees that are larger you should consult an expert tree removal service first.
Remove Shrubs
Once the trees are taken down The next step is to remove any large-sized or mid-sized trees. Based on their size, some might be able to be removed manually, however, others require a shovel to remove the roots. It is possible to cut back a few of the smaller branches or parts of a tree to make digging them out a bit easier.
Cut down a small tree
The trunk should be marked around 1 foot above the ground. Cut the tree at an angle of 45 degrees with either an axe or chainsaw until you’re about a third your way to the tree. Be sure to cut into the opposite side of the tree that you would prefer for the tree’s fall to be to. Make a wedge of 45 degrees along the opposite aspect of your tree. It should be slightly higher than the cuts on your opposite. The cut should be around halfway across the trunk. The tree should be pushed away towards the opposite side of the tree where you cut your second slice. If the tree isn’t able to fall, use the bow saw to keep making your cutting until your tree starts to fall. Repeat steps 1-4 to remove the trees you’d like to take away.
Remove a stump
After the trees have been being cut down, it is necessary to get rid of the stump in order in order to rid your property of any remaining brush. There are many ways to accomplish this however it is dependent on the amount and size. Here are some methods to eliminate them: Use a shovel to clear them. This is best for smaller stumps with roots that are shallow. It is possible to expose the roots by digging them out, and then use an axe or pruning shears to break the stump free. Then, you can pull the stump from the soil. Utilize a stump grinder to remove the stumps. This is a good option for small stumps that have an unruly root system and medium to large stumps that have shallow roots. Grinders are typically available from local home improvement stores at the hourly cost. When using either a shovel or stump grinder, make certain to fill in the hole with topsoil or dirt to create flat surfaces.
Clear out the underbrush
When the bigger items have been removed, it’s time to remove underbrush. The tall grass, weeds tiny shrubs, and vines remain getting in the way, which means it’s time to get out the weed trimmer, machete, scythe and pruner and begin to work. If you’re not wearing long sleeves and pants at this point, make sure you wear them now. They’ll protect your skin from the harmful effects of plants such as poison ivy or poison oak that could be hiding.
Trim the remainder
The final part is straightforward. Cut off the remaining vegetation using the scythe or string trimmer. It is best to cut at the lowest point you are able to. In the event that your overgrowth grows especially excessively high, cut it down to about half on the initial pass, and cut it back to the ground in a subsequent run. If the brush you want to trim is especially thin, you can employ the lawnmowers to take care of this task. But, you might have to scrub the mower’s deck frequently often. As trimming, make sure to keep your eyes out for any bushes or larger vines that you might miss while trimming the brush.
Cleanup time
It’s getting close! You’re ready to take out your rake and get to getting rid of the brush. There is no correct or incorrect way to cut the brush. Keep in mind that the brush needs to be removed in the future, so be sure to build piles with the disposal method in mind – whether it’s the compost heap or your weekly trash pickup, or a garden waste dumpster
